How do I fix error code F9?

How do I fix error code F9?

The F9 error usually means the door switch circuit system is faulty. This can be addressed by checking the door switch itself. If the door switch is dirty or caught in one position, use a damp cloth to wipe the switch clean and then wiggle the switch slightly to make sure the switch moves back and forth.

How do I fix the F9 on my Whirlpool oven?

F9 – Oven Door Lock Failure – Check door lock switches and wiring. Check for stuck lock switch. FH – Detects No Water Entering Machine or No Pressure Switch Trip – Select ‘cancel’ twice to clear this code. If there is NO water in the unit, make sure the valves are turned on all the way.

What does E2 F3 mean on Whirlpool?

An E0-F3 error indicates that the oven’s temperature sensor is open; E1-F3, that the temperature sensor is shorted; E2-F3, that the oven temperature has exceeded the maximum rated 575 degrees Fahrenheit in “Cook” mode; and E3-F3, that the oven temperature has exceeded the maximum rated 950 degrees Fahrenheit in “Clean” …

What does EO F2 mean on Whirlpool?

shorted keypad
Ranges , Whirlpool , Appliances. The “F2-EO” fault code indicates a shorted keypad. The electronic range control (ERC) will need to be replaced. I recommend calling a service technician to diagnose and repair your range.

What does F9 error code mean?

An F9 error code on an LG oven means that the oven has failed to exceed 150 degrees Fahrenheit after five minutes of preheating.

Why is my Whirlpool stove saying F9?

This code will most often indicate that the appliance is wired incorrectly at the home electrical supply or the hardwire connection. If your range was installed recently and is not functioning, contact a qualified electrician to verify the electrical supply.

What does code F9 mean on a Whirlpool stove?

During a power outage, if there was a surprising amount of power supply line “noise” that the control detected as an incorrect voltage amount, the control could display the F9, F9 E0, or PF Error Code.

What is E2 error in washing machine?

If the LED Lights are flashing with an E2, 5C or 5E error, it is an indication of water drainage issue. Water is not draining from the drum. To resolve the error issue, check the following: • Check drainage pump filter for blockages (e.g. lint, coins hair, clips)

How do I clear the error code on my Whirlpool washer?

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

How do I fix F1 error on Whirlpool oven?

If you receive a two-digit error code reading F1, your Whirlpool range may be experiencing one of three problems. There may be an analog to digital failure; if this is the case, simply disconnect the range for 30 seconds and plug back in. If the same display reappears, you may need to replace the control board.

What does error code E02 and F06 on Maytag washer mean?

F06 E02 is a communication error because your MCU and your CCU (central control unit). You’ll want to remove the top panel, the control panel, and then the front panel of the washer and make sure the wire connections to the motor control unit below the tub are all secure.

What does Whirlpool duet washer error code F- mean?

The Whirlpool Duet washer has a series of error codes that indicate specific problems. The F/dL code indicates a door lock error on the machine. When the door fails to lock to allow the cycle to begin, it attempts to lock itself at least six times before the error appears on the digital display screen.

What does Code F mean on a whirlpool washer?

Whirlpool Duet washing machine error codes are seen on the digital display as: F# and E# OR just as F#. The “F” error code indicates the washing machine system or “Fault”. Ehe “E” error is indicating the part in your washer that causing the issue or “Error”.

What does error code SD mean on a whirlpool washer?

Error code SD means LONG DRAIN. This error appears when the drain time exceeds 8 minutes and the water valves turn off. After 4 minutes the “Sd” error will be displayed, and then 4 minutes later the F21 error code will be displayed.

How do I fix error code F9? The F9 error usually means the door switch circuit system is faulty. This can be addressed by checking the door switch itself. If the door switch is dirty or caught in one position, use a damp cloth to wipe the switch clean and then wiggle the switch slightly…